Farmers Guradian
Topics
Nine ways to keep your farm vehicles safe

Nine ways to keep your farm vehicles safe

Arable Farming Magazine

Arable Farming Magazine

Dairy Farmer Magazine

Dairy Farmer Magazine

British Farming Awards

CropTec

LAMMA 2019

New to Farmers Guardian?
Register Now
Login or Register
New to Farmers Guardian?
Register Now
New to Farmers Guardian?
Register Now

You are viewing your 1 free article

Register now to receive 2 free articles every 7 days or subscribe for unlimited access.

Subscribe | Register

Buyer's guide: Fancy a Komatsu excavator for general farm use?

If you fancy an excavator for general use, there is plenty of choice in the 13-tonne sector, but what should you be looking for?

 

Geoff Ashcroft takes a look at a popular Komatsu PC138US.

TwitterFacebook
Share This

Buyer's guide: Fancy a Komatsu excavator for general farm use?

With a range of excavators from one to 300 tonnes, it is fair to say Japanese construction machinery firm Komatsu knows a thing or two about diggers.

 

One of its more popular models is the PC138US. It sits in the 13-tonne category, but offers a short rear radius, which means the counterweight barely sticks out over the tracks.

 

Compared to the firm’s regular PC130, the short radius model is much easier to work with in confined spaces without worrying about what the back end might bash.

 

Ideal then, for occasional farm-based operations. The PC138US is still a current machine, but now carries a dash 11 suffix, along with all the emissions-based paraphernalia associated with it.

 

This 2005 model PC138US-2 was sold in the UK from 2000-2006, until the PC138US-8 rolled in meeting EU Stage 3a regulations with common rail fuel injection, a revised turbocharger and a couple more horses, along with a lower working noise level.

 

Changes

 

Little has altered over the years. In the change from dash 2 to dash 8, the latter machine gained better sound insulation, larger mirrors for better visibility, and the switch from emery-paper-type non-slip floor plates to a punched-plate design.

 

You might also find one with an optional dozer blade on its undercarriage.

 

Field service engineer Dale Gilberston from UK distributor Marubeni-Komatsu guides us around this 12-year-old, 5,000-hour PC138US-2.

ENGINE

ENGINE

Almost buried inside the counterweight is a Komatsu four-pot turbo diesel pushing out 88hp for the PC138US-2.

 

You will need to climb up the off-side front and onto the top of the machine to lift the bonnet and peer inside.

 

This one is a Stage 2 complaint unit, and is not burdened by EGR valves, DPF, SCR catalyst or common rail injection.

 

It is also has a non-variable geometry turbocharger and the mechanical fuel injection pump is cable controlled, but uses an electric throttle controller in the cab.

 

However, the mechanically straight-forward four-pot can suffer blow-by if not worked hard.

 

Mr Gilberston says: “It usually points to piston rings and bores, but most should have been sorted during their lifetime while under warranty.

 

“Look at the engine breather; if oil spots appear on the undercarriage, it is likely to need some attention.”

 

He says you should not fear a high-hour machine if it has been well looked after and worked hard.

HYDRAULIC SYSTEM

The life-blood of an excavator is its hydraulic system. And there are 70 litres inside the PC138US-2.

 

A sight glass lets you assess oil level and the colour, with the latter being a good indication of oil condition.

 

Dark hydraulic oil suggests it might have over-stayed its welcome, and is also an indication the oil has become hot.

 

My Gilberston says: “It can happen when a machine spends a long time on a hydraulic breaker. Check the handbook to know where to position the boom, arm and bucket before you can check the correct hydraulic oil level, as every machine is measured differently.”

 

Operate the machine and listen for pump noise when carrying out several functions at once.

 

The hydraulic system is not the quietest of machines, but a screaming pump under heavy load can suggest cavitation and a loss of hydraulic power.

 

“The tracks draw 100 per cent of pump power, so dial in full throttle and just track the machine around. It should move easily and should have power enough in one track to turn the machine.”

 

Mr Gilberston suggests putting the bucket on the ground at the side of the tracks and easing one track off the ground.

 

He says: “Run one track for a minute in either direction and cycle the track speed change to make sure it works.

 

“If it stays permanently in low, you will be looking at a replacement track motor.”

CAB

CAB

Operator space is a compromise with short-radius excavators, simply because there is a lot to fit on a smaller upper-structure.

 

Mr Gilberston says: “Sliding doors can suffer roller failure and the door drops when you open it. It is an inconvenience, because you will need to lift the door if you want to latch it open.”

With low pressure pilot controls, he suggests looking for oil below the joysticks.

 

“Older machines can suffer leaks from O-ring seals or pipe failure. And pipes run under the cab to the valve block in the rear, so it is not a five-minute job.”

 

The dash 2’s monitor was superceded by a 7in TFT version in the dash 8 model. Check functions work as they should.

 

Mr Gilberston says: “The monitor should not be cracked or the buttons split or broken. You cannot replace the buttons; it will result in a new monitor.”

 

The PC138 also gets a tin roof hatch with window glass. They are known to collect water and can rot through.

 

He says: “Get a colleague to pour a bucket of water over the cab roof and make sure it does not leak.”

TYPICAL PC138US PRICES

  • 2015 PC138US-10, blade, a/c, 3-speed tracking, 2,300 hours: £66,500
  • 2008 PC138US-8, quick hitch, piped, a/c, 9,000 hours: £23,000
  • 2005 PC138US-2, 11,600 hours: £20,300
  • 2005 PC138US-2, quick hitch, 5,000 hours: £19,000

UNDERCARRIAGE

UNDERCARRIAGE

The PC138US-2 will most likely be sat on 600mm wide, triple grouser track shoes which bolt onto a track chain.

 

Each assembly wraps around a frame which uses seven lower rollers and one upper track roller, with a drive sprocket at the rear and an idler at the front.

 

If the machine has done very little running about, track pins can seize and adjacent track shoes will sit in a ‘V’ formation.

 

Mr Gilberston says: “Look at the drive sprocket teeth for an idea of how much life might be left in it. If teeth are thin and sharp, it will need refreshing.

 

Concern

 

“It is a similar concern with track chains and pins which run against sprockets; just feel them carefully. Round pins suggest an undercarriage with little wear, and a high-hour machine is likely to have had its undercarriage renewed.”

 

He says lift one track off the ground at each time to inspect the rollers: “Track rollers can seize, but they can also suffer from collapsed bearings too.

 

"If the bearings have failed, there will be a lot of play visible once the weight is off them.”

 

Track tension is achieved by pumping grease into the track tensioning cylinders.

 

Mr Gilberston says: “Do not over-do it. Too tight is as bad as too slack, and if grease seals are failing, track tension will slacken fairly quickly after you have tensioned them.”

Retail parts prices (+VAT)

Track motor: £11,529.87

Track roller assembly: £247 each

Carrier rollers: £118.75 each

Tipping link pin: £220.08

Cab door rollers: £451.93 (full set)

Starter motor: £579.76

DIGGING EQUIPMENT

DIGGING EQUIPMENT

The business end is where you will find the bucket, arm and boom. And all joints are connected using pins and bushes.

 

If not greased regularly, there will be wear and free-play aplenty, though some play is inevitable.

 

The PC138 uses a 4.6-metre one-piece boom and the longest arm which could be fitted. In this instance, a 3m unit, which gives a horizontal reach of 7.8m and a maximum dig depth of 5m.

 

It is a generous working range, but the compromise is a smaller bucket than you might expect.

 

Mr Gilberston says: “Again, place the bucket on the ground and gently move the joysticks to ease load on and off the machine.

 

“You will soon see which pins and bushes are the most worn. Pay attention to the boom foot, as this will be a major job to replace.

 

“You will need to decide what is acceptable and what needs to be replaced. Pin swaps are relatively easy; bushes will probably need to be pressed in and out.”

 

Pushing the arm all the way out and lowering the boom will make it easy to check ram seals and pipework and look for stress cracks around any of the boom and arm joints.

SPECIFICATIONS

Model: Komatsu PC138US-2

Machine weight: 13,500-15,000kg

Engine: Stage 2 compliant, 88hp Komatsu four-cylinder turbo

Tracks: 500mm, 600mm and 700mm triple grousers

Travel speed: 2.9kph (1.8mph) and 5.1kph (3.2mph)

Boom: 4.6-metre one-piece boom

Arm: 2.1m, 2.5m and 3m

Win a New Holland T6 DCT!

Win a New Holland T6 DCT!

Farmers Guardian has joined up with New Holland to give a lucky reader the chance to experience the new T6 DCT for 12 months!

 

New Holland Agriculture has enriched the T6 Series offering with the new T6 Dynamic CommandTM, an all round multi-purpose tractor.

 

It is a versatile tractor that will be an asset to the fleets of arable, livestock, dairy farmers, contractors and hay and forage operations.

 

CLICK HERE

TwitterFacebook
Post a Comment
To see comments and join in the conversation please log in.

Most Recent

Facebook
Twitter
RSS
Facebook
Twitter
RSS